Кафедра металургії чавуну і сталі (ДМетІ) (з 2022 р до складу кафедри увійшла кафедра Інженерна педагогіка ІПБТ)

Permanent URI for this community

http://crust.ust.edu.ua/handle/123456789/14580
ENG: Department of Iron and Steel Metallurgy (Dnipro Metallurgical Institute, DMetI)

Browse

Browsing Кафедра металургії чавуну і сталі (ДМетІ) (з 2022 р до складу кафедри увійшла кафедра Інженерна педагогіка ІПБТ) by Author "Boyko, Maksym M."

Now showing 1 - 2 of 2
  • Thumbnail Image
    Item
    Application of Biomass Pellets for Iron Ore Sintering
    (Trans Tech Publications Ltd, Switzerland, 2021) Kieush, Lina; Koveria, Andrii; Qiao Zhu, Zuo; Boyko, Maksym M.; Sova, Artem; Yefimenko, Vadym
    ENG: Purpose. The use of biomass as fuel might solve several technological and environmental issues and overcome certain challenges of sinter production. In particular, as revealed by comprehensive analyses, biomass can be used as fuel for iron ore sintering. In this study, we investigate the use of some raw and pyrolysis-processed biomass pellet types, namely wood, sunflower husks (SFH), and straw, for iron ore sintering. In the experiments, the pyrolysis temperature was set to 673, 873, 1073, and 1273 K, and the proportion of biomass in the fuel composition was set to 25%. It was established that the addition of biofuels to the sintering blend leads to an increase in the gas permeability of the sintered layer. The analysis of the complex characteristics of the sintering process and the sinter strength showed the high potential of wood and sunflower husk pellets pyrolyzed at 1073 and 873 K, respectively, for iron ore sintering. The analysis of the macrostructure of the sinter samples obtained using biomaterials revealed that with higher pyrolysis temperatures; the materials tend to have greater sizes and higher amounts of pores and cracks. The composition analyses of the resultant sinters revealed that with higher temperature, the FeO content of the sinters tends to increase.
  • Thumbnail Image
    Item
    Influence of Biocoke on Iron Ore Sintering Performance and Strength Properties of Sinter
    (Dnipro University of Technology, Dnipro, Ukraine, 2022) Kieush, Lina; Koveria, Andrii; Boyko, Maksym M.; Yaholnyk, Maksym V.; Hrubiak, Andrii; Molchanov, Lavr; Moklyak, Volodymyr
    ENG: Purpose. The research purpose is to substantiate the use of biocoke as a fuel in the iron ore sintering, as well as its influence on the performance and properties of the resulting sinter. To completely replace conventional coke breeze, biocoke is produced using 5 wt.% biomass wood pellets at different carbonization temperatures of 950 or 1100°C. Further, the influence of biocoke on the sintering process and the sinter quality is studied at a high proportion of biomass pellets of 10, 15, 30, 45 wt.% and a carbonization temperature of 950°C. Methods. Carbonization is performed in shaft-type electric furnaces to produce laboratory coke or biocoke. Afterward, the sintering of iron ores is conducted on a sinter plant. To assess the sintering process and the quality of the resulting sinter, the filtration rate is determined on a laboratory sinter plant using a vane anemometer designed to measure the directional flow average velocity under industrial conditions. The sinter reducibility is studied using a vertical heating furnace to assess the effect of coke and biocoke on the sinter’s physical-chemical properties. Findings. It has been determined that biocoke, carbonized at a temperature of 950°C, has good prospects and potential for a shift to a sustainable process of iron ore sintering. Originality. It has been proven that biocoke with a biomass pellet ratio of up to 15 wt.%, obtained at a temperature of 950°C, does not affect the parameters characterizing the sintering process. The sinter strength indicators correspond to the use of 100 wt.% conventional coke breeze. Biocoke used with a high proportion of biomass pellets of 30 and 45 wt.% causes a deterioration in the sinter quality. Practical implications. The results of using biocoke with the addition of 5-15 wt.% biomass pellets and at a temperature of 950°C are within the standard deviation, which makes it possible to use biocoke with 15 wt.% biomass pellets instead of industrial coke breeze.