Browsing by Author "Parneta, Bogdan Z."

Now showing 1 - 3 of 3
  • Thumbnail Image
    Item
    A Comprehensive Procedure for Estimating the Stressedstrained State of a Reinforced Concrete Bridge Under the Action of Variable Environmental Temperatures
    (РС ТЕСHNOLOGY СЕNTЕR, Kharkiv, Ukraine, 2021) Kovalchuk, Vitalii V.; Onyshchenko, Artur; Fedorenko, Olexander; Habrel, Mykola; Parneta, Bogdan Z.; Voznyak, Oleh M.; Markul, Ruslan V.; Parneta, Mariana; Rybak, Roman
    ENG: This paper reports the full-scale experimental measurements of temperature distribution over the surfaces of bridges’ steel-concrete beams under the influence of positive and negative ambient temperatures. It has been established that the temperature is distributed unevenly along the vertical direction of a bridge’s steel-concrete beam. It was found that the metal beam accepted higher temperature values. The maximum registered temperature difference between a metal beam and a reinforced concrete slab at positive ambient temperatures was +9.0 °C, and the minimum temperature difference was −2.1 °C. The mathematical models for calculating a temperature field and a thermally strained state of bridges’ steel-concrete beams under the influence of variable climatic temperature changes in the environment have been improved, taking into consideration the uneven temperature distribution across a bridge’s reinforced concrete beam. The possibility has been established to consider a one-dimensional problem or to apply the three-dimensional estimated problem schemes as the estimation schemes for determining the thermoelastic state of reinforced concrete bridges. The temperature field and the stressed state of bridges’ reinforced concrete beams were determined. It was found that the maximum stresses arise at the place where a metal beam meets a reinforced concrete slab. These stresses amount to 73.4 MPa at positive ambient temperatures, and 69.3 MPa at negative ambient temperatures. The amount of stresses is up to 35 % of the permissible stress values. The overall stressed-strained state of a bridge’s reinforced concrete beams should be assessed at the joint action of temperature-in- duced climatic influences and loads from moving vehicles.
  • Thumbnail Image
    Item
    Evaluation Deflected Mode of Point Frogs Mark 1/11 Finite Element Method
    (НВП ПП «Технологічний Центр», Харків, 2017) Kovalchuk, Vitalii V.; Bolzhelarskyi, Yaroslav V.; Parneta, Bogdan Z.; Pentsak, Andriy; Petrenko, Oleksiy V.; Mudryy, Ihor B.
    EN: We carried out evaluation of the stressed-strained state of crossings of turnouts by the finite element method in the Ansys programming complex. It was established that under conditions of three-axial compression, at large stresses of vertical compression, the cracks of multi-cycle metal fatigue of the crossing develop. It was found that the development of defects by the code DS 14.1-14.2 on the rolling surface of the cast part of a wing rail and the crossing’s core occurs due to high contact stresses near the edge of the working face of a wing rail and the crossing’s core. They occur in this region in the form of cyclically repeated and sign-alternating normal and tangential stresses from cyclically recurring power impacts from the wheels of rolling stock of railroad transport. It was established that for the normal stresses, values that are maximal by absolute magnitude correspond to the moment when a wheel passes the estiamted cross section of the crossing. For the tangential stresses, on the contrary, at the moment when the wheel is over the estimated cross section, their magnitude is close to zero. The obtained results of the stressed-strained state of crossings are necessary for the optimal design of transverse and longitudinal profiles of the crossing. This will make it possible to extend operation life cycle of the crossings of turnouts and save state budget resources for their current maintenance and repair.
  • Thumbnail Image
    Item
    Investigating the Influence of the Diameter of a Fiberglass Pipe on the Deformed State of Railroad Transportation Structure “Embankment-Pipe”
    (РС Тесhnology Сеntеr, 2022) Kovalchuk, Vitalii V.; Sobolevska, Yuliya; Onyshchenko, Artur; Bal, Olena M.; Kravets, Ivan B.; Pentsak, Andriy; Parneta, Bogdan Z.; Kuzyshyn, Andriy; Boiarko, Vladyslav; Voznyak, Oleh M.
    ENG: This paper has analyzed the use of fiberglass pipes in the body of the railroad embankment by a method of pushing them through the subgrade. A flat rod model has been improved for assessing the deformed state of the transport structure "embankment-fiberglass pipe" by a method of forces when replacing the cross-section of the pipe with a polygonal one. The analytical model accounts for the interaction between the pipe and soil of the railroad embankment. To this end, radial and tangential elastic ligaments are introduced into the estimation scheme, which make it possible to simulate elastic soil pressure, as well as friction forces that occur when the soil comes into contact with the pipe. The deformed state of the transport structure "embankment-fiberglass pipe" was calculated by the method of forces and by a finite-element method under the action of load from the railroad rolling stock, taking into consideration the different cross-sections of the pipe. It has been established that with an increase in the diameter of the fiberglass pipe, the value of deformations of the subgrade and fiberglass pipe increases. With a pipe diameter of 1.0 m, the deformation value in the vaulted pipe is 2.12 mm, and with a pipe diameter of 3.6 m – 4.16 mm. At the same time, the value of deformations of the subgrade under the sleeper is 5.2 mm and 6.0 mm, respectively. It was determined that the maximum deformations of the subgrade, which occur above the pipe, with a pipe diameter of 3.6 m, are 4.46 mm. At the same time, the maximum vertical deformations of a fiberglass pipe arise in the pipe vault and, with a pipe diameter of 3.6 m, are 4.16 mm. It has been established that the maximum horizontal deformations of the subgrade occur at points of horizontal diameter of the fiberglass pipe while the minimal horizontal deformations of the subgrade occur at points lying on the vertical diameter of the pipe.