Розробка моделі процесу взаємодії компонентів двофазного потоку, введеного в чавун, при інжекційній десульфурації
Loading...
Date
2025
Journal Title
Journal ISSN
Volume Title
Publisher
Український державний університет науки і технологій, ІВК «Системні технології», Дніпро
Abstract
UKR: Фактичні результати промислового застосування позапічної десульфурації свідчать, що практичні результати застосування технології в багатьох випадках не є досить стійкими. Дослідження були проведені на розрахункових та "холодних" фізичних моделях. В якості десульфуруючих реагентів оцінені магній, мелене вапно, карбід кальцію. На основі фактичних результатів фізичного моделювання та подальших розрахунків був сформульований поліпшений вираз для розрахунку глибини занурення струменя в залежності від параметрів інжекційної занурювальної фурми. Показано, що під час інжекційної десульфурації чавуну газовий компонент потоку зупиняє свій напрямний рух у розплаві до 80 мм (фактично 50-60 мм), тверді частки продовжують рухатися у порожнині та вдаряються у поверхню цієї порожнини. Для оцінки подальшого руху частинки через межу "газова порожнина-розплав" була розроблена модель для визначення глибини занурення частинок реагенту як функції швидкості вдування двофазного потоку.
ENG: Actual results of the industrial application of out-of-furnace desulfurization indicate that practical results of the technology in many cases are not sufficiently stable. The studies were conducted on computational and "cold" physical models. Magnesium, ground lime, calcium carbide - desulfurizing reagents. Based on the actual results of physical modeling and further calculations, improved expression was formulated for calculating the depth of jet immersion depending on the parameters of the injection lance. It is shown that during injection desulfurization of cast iron, the gas component of the flow stops its directional movement in the melt up to 80 mm (actually 50-60 mm), solid particles continue to move in the cavity and hit the surface of this cavity. To assess further movement of the particle through the "gas cavity-melt" boundary, model was developed to determine the depth of immersion of reagent particles as a function of the injection velocity of the two-phase flow.
ENG: Actual results of the industrial application of out-of-furnace desulfurization indicate that practical results of the technology in many cases are not sufficiently stable. The studies were conducted on computational and "cold" physical models. Magnesium, ground lime, calcium carbide - desulfurizing reagents. Based on the actual results of physical modeling and further calculations, improved expression was formulated for calculating the depth of jet immersion depending on the parameters of the injection lance. It is shown that during injection desulfurization of cast iron, the gas component of the flow stops its directional movement in the melt up to 80 mm (actually 50-60 mm), solid particles continue to move in the cavity and hit the surface of this cavity. To assess further movement of the particle through the "gas cavity-melt" boundary, model was developed to determine the depth of immersion of reagent particles as a function of the injection velocity of the two-phase flow.
Description
І. Маначин: ORCID 0000-0001-9795-6751; В. Кисляков: ORCID 0000-0002-1775-5050; М. Рибальченко: ORCID 0000-0001-5162-5201
Keywords
реагент, частинка, модель, занурення, магній, вапно, reagent, particle, model, immersion, magnesium, lime, КГМ
Citation
Маначин І. О., Єлісєєв В. І., Кисляков В. Г., Рибальченко М. О. Розробка моделі процесу взаємодії компонентів двофазного потоку, введеного в чавун, при інжекційній десульфурації. Інформаційні технології в металургії та машинобудуванні – ІТММ’2025 : тези доп. Міжнародної наук.-техн. конф. (м. Дніпро, 23-24 березня 2025 р.). Дніпро, 2025. C. 317–323. DOI: 10.34185/1991-7848.itmm.2025.01.056.