Вплив технологічних параметрів на стабільність одиничного треку при селективному лазерному плавленні сплаву Inconel 718
Loading...
Date
2023
Journal Title
Journal ISSN
Volume Title
Publisher
Український державний університет науки і технологій, ІВК «Системні технології», Дніпро
Abstract
UKR: При селективному лазерному плавленні продукт складається з набору окремих шарів, які, у свою чергу, створюються з набору окремих доріжок. Зразки друкували на 3D-принтері Alfa-150 виробництва ТОВ «АЛТ Україна». Одиночні доріжки були створені на базовій колодці з того ж матеріалу. При цьому потужність лазера змінювалася в діапазоні 100...150 Вт з кроком 10 Вт, а швидкість лазерного променя - в діапазоні 1300...3500 мм/с з кроком. 100 мм/с. Всього досліджено 108 режимів друку одиночних доріжок, розташованих на відстані 1,5...2 мм одна від одної. Кожен блок містить 6 груп по 3 одиночних треків, створених в одному режимі. Товщина шару, що використовується в експериментах, становить 30 мкм. Стійкість і якість колії визначається кількістю питомої енергії. Зі зменшенням значення питомої енергії.
ENG: With selective laser melting, the product consists of a set of single layers, which in turn are created from a set of single tracks. Samples were printed on an Alfa-150 3D printer manufactured by ALT Ukraine LLC. Single tracks were created on a base pad made of the same material. At the same time, the laser power was changed in the range of 100...150 W with a step of 10 W, and the speed of the laser beam - in the range of 1300...3500 mm/s with a step of 100 mm/s. A total of 108 printing modes of single tracks, located at a distance of 1.5...2 mm from each other, were investigated. Each block contains 6 groups of 3 single tracks made in the same mode. The thickness of the layer used in the experiments is 30 μm. The stability and quality of the track is determined by the amount of specific energy. With a decrease in the value of the specific energy.
ENG: With selective laser melting, the product consists of a set of single layers, which in turn are created from a set of single tracks. Samples were printed on an Alfa-150 3D printer manufactured by ALT Ukraine LLC. Single tracks were created on a base pad made of the same material. At the same time, the laser power was changed in the range of 100...150 W with a step of 10 W, and the speed of the laser beam - in the range of 1300...3500 mm/s with a step of 100 mm/s. A total of 108 printing modes of single tracks, located at a distance of 1.5...2 mm from each other, were investigated. Each block contains 6 groups of 3 single tracks made in the same mode. The thickness of the layer used in the experiments is 30 μm. The stability and quality of the track is determined by the amount of specific energy. With a decrease in the value of the specific energy.
Description
Р. Подольський: ORCID 0000-0002-0288-0641
Keywords
одна доріжка, питома енергія, режим, Inconel 718, single track, specific energy, mode, КМТОМ
Citation
Аджамський С. В., Кононенко Г. А., Подольський Р. В. Вплив технологічних параметрів на стабільність одиничного треку при селективному лазерному плавленні сплаву Inconel 718. Інформаційні технології в металургії та машинобудуванні – ІТММ’2023 : тези доп. Міжнародної наук.-техн. конф. (м. Дніпро, 22 березня 2023 р.). Дніпро, 2023. C. 8–11. DOI: https://doi.org/10.34185/1991-7848.itmm.2023.01.002.