Кафедра ливарного виробництва (ДМетІ)

Permanent URI for this community

http://crust.ust.edu.ua/handle/123456789/15008

ENG: Department of casting production (DMetI)

Browse

Now showing 1 - 20 of 91

Assessing Criteria for Casting and Deformation Suitability of Metals and Alloys
(Dnipro University of Technology, Dnipro, 2025) Kimstach, Tetiana V.; Uzlov, Kostiantyn I.; Bilyi, Oleksandr P.; Mazorchuk, Volodymyr F.; Repyakh, Serhii I.
ENG: Purpose. Based on existing criteria for predicting the suitability of metals and their alloys for manufacturing products from them by deformation or casting analysis develop a set of dimensionless parametric criteria and their quantitative scales. Their using will allow increasing the predicting accuracy of metals and alloys for their processing by pressure or casting suitability and feasibility. Methodology. The work uses phenomenological approach to systematic analysis results of metals and alloys mechanical and individual casting properties interpreting under uncertainty conditions, drawing on literature reference data, expert evaluation data and the authors’ own research results. The authors’ own data have been obtained experimentally using standard methods for mechanical properties determining and due to original authors’ method for technical purity metals and alloys based on them cast samples values of their absolutely hindered linear shrinkage determination during casting. Findings. The authors first proposed parametric dimensionless criteria and scales to them (criteria groups). Their application allows one, through such groups combinations, to assess suitability of any alloy or metal for its use possibility for products manufacturing by casting and/or pressure processing. Originality. For the first time dimensionless parametric criteria have been developed and proposed for use at initial stages of new alloys or technologies elaboration for products from them manufacturing as well as their quantitative scales for preliminary assessment (prognosis) of alloys processing feasibility by pressure or casting, regardless of their type and method. Practical value. Developed criteria and their quantitative scales using will allow alloys developers and specialized enterprises employees to save time and expenses both for alloy elaboration and for its implementation into production.
Complex of Mathematical Models and Methods to Calculate Pressure Effect on Sulfide Distribution in Steel
(Хмельницький національний університет, Україна, 2021) Selivyorstova, Tetjana V.; Selivyorstov, Vadim Yu.; Kuznecov, Vitaliy V.
ENG: Primary objective is to develop computational method to analyze digital pictures of sulfide prints, helping obtain qualitative image characteristics, and to formulate mathematical model of the distribution of sulphide inclusions to determine specific features of the pressure effect on the macrostructure formation of carbon steel castings flooded into the uncooled mold. The research was carried out using images of sulfide prints of templates cut of steel cylindrical castings; L500 steel was applied. The castings result from industrial tests of a method of gas-dynamic effect on the fusion in the foundry forms under the conditions of a casthouse of Dnipropetrovsk aggregate plant PJSC. Digital pictures of sulfide prints, obtained in terms of the increased rate of gas pressure and maximum pressure, were binarized; defective fra gments were removed; and zo ning took place. The developed computational method has been applied for fragments of images, representing different zones; data arrays have been received containing sizes and amounts of inclusions in the fragment. The developed computational method to analyze digital images of sulfide prints has been implemented. ASImprints software support has helped obtain qualitative characteristics of images; namely, distribution of amount of the certain-size sulfide inclusions. The computational method to analyze digital images of sulfide prints has made it possible to study the set of patterns of sulfide prints. The dependences have been obtained, describing specific features of sulfide inclusion distribution while varying gas-dynamic pressure method in terms of fusion in the casting form. It has been demonstrated that the distribution describes effectively the power-series distribution to compare with the exponential one. Mathematical model of the power -series distribution parameter dependence upon pressure has been developed. Deviation of the distribution parameters in terms of the experimental values and the model values has been evaluated. The research demonstrates the ways to apply an algorithm of simple recursive casting for quantitative analysis of digital images of sulfide prints. Use of ASImprints, being software implementation of the computational method to analyze digital images of sulfide prints making it possible to obtain qualitative characteristics of images, has helped identify that the increased pressure within a casting-device for gas injection system results in the increased specific amount of inclusions and the decreased specific zone of sulfide inclusions respectively. It has been defined that exponential function describes reliably the nature of sulfide inclusion distribution in the digital image of sulfide print. The research has demonstrated that fragments of a sulfide print, belonging to one zone, are statistically homogeneous. Thus, it is possible to analyze quantitively digital image zone of a sulfide print on its fragment. Mathematical model of dependence of sulfide inclusion distribution in carbon-steel castings in terms of gas-dynamic effect on fusion solidifying in a mold has been developed. The model may be applied to predict sulfide inclusion distribution within the selected zones of cross section of the cylindrical castings solidifying in the uncooled mold in terms of the preset mode of gas-dynamic effect.
Construction of a Kinetic Equation of Carbon Removal for Controlling Steel Melting in the Metallurgical System "Cupola Furnace – Small Converter"
(TECHNOLOGY CENTER PC, Kharkiv, 2025) Makarenko, Dmytro M.; Selivorstova, Tetiana V.; Dotsenko, Yuriy V.; Osypenko, Iryna O.; Dzevochko, Oleksandr M.; Pereverzieva, Alevtyna M.; Dzevochko, Alona I.
ENG: The object of research in the paper is the process of steelmaking in a small converter, which works in tandem with a cupola furnace. The existing problem is that the control of the process of obtaining steel in an oxygen converter is complicated by the need to determine in real time the current chemical composition of the melt, in particular carbon. This is due to the fact that the rate of carbon removal is too high, as a result of which the process of carbon removal is transient. Therefore, it is too difficult to implement regulation based on feedback on continuous measurement. The presence of the specified problem requires solutions related to the possibilities of developing or improving software control of the process. It is shown that in certain sections of the process within each time section of oxygen purging of the melt in the converter, the kinetic curve has a linear form with a constant coefficient value in front of the inlet mine. But the value of the initial coefficient for each equation that describes the process within its limits changes. This allows to state that in case of a change in the initial condition, the kinetic curves shift relative to each other in parallel. On this basis, a system of equations has been constructed that describes the process of carbon removal in a small oxygen converter that receives liquid iron from a cupola furnace. It has been shown that to use the obtained system of equations, it is necessary to know the initial carbon content in the melt discharged from the cupola furnace, and it depends on the method of oxygen supply to the cupola furnace. Based on the modeling of this process in two variants – using a “sharp blow” and supplying oxygen to the air blown into the tuyeres, a nomogram has been constructed. It allows to determine the initial carbon content for the practical use of the obtained system of equations. Using the obtained system makes it possible to determine the time after which oxygen cutoff should be made. This will allow to decide to implement software control of the melt blowing process in the converter. The presented study will be useful for machine-building enterprises that have foundry shops in their structure, where cast iron is smelted for the manufacture of castings.
Corrosion Resistance of Reinforced Layers of 15х11МФ Steel Steam Turbine Blades
(Національний науковий центр «Харкiвський фiзико-технiчний інститут», 2021) Hlushkova, D. B.; Bahrov, V. A.; Hrinchenko, O. D.; Hnatiuk, A. A.; Kalinina, N. E.; Kalinin, V. T.
ENG: The reliability of the vane apparatus of steam turbines largely determines the operation of the turbine as a whole. The results of scientific research indicate that the surface operation of the blades in the wet-steam flow is caused by a combination of corrosion and drip erosion. The presence of chemical elements and compounds in the working fluid intensifies the process of blade wear. The pH value of the working environment, which can fluctuate significantly during operation, has a significant effect on the wear characteristics. The influence of methods of strengthening the leading edges of steam turbine blades made of steel is analyzed 15H11MF on corrosion resistance. Corrosion tests of blade samples were carried out, the inlet edges of which were strengthened in three ways: high current amplification, electrospark alloying with T15K6 alloy, electrospark alloying with steel 15H11MF. According to the results of the tests, the layer strengthened by hardening by high-frequency currents has the lowest corrosion rate, the layer strengthened by electrospark alloying with T15K6 hard alloy has the highest. The corrosion rate of the layer reinforced by electrospark alloying of steel 15H11MF is 2.1 less than that of the layer reinforced with T15K6 alloy.
Determining the Thermally-Stressed State of Motor-Driven Bowls for Transporting Liquid Slag
(РС ТЕСHNOLOGY СЕNTЕR, Kharkiv, 2024) Povorotnii, Viktor V.; Shcherbyna, Iryna V.; Zdanevych, Serhiі V.; Diachenko, Nina K.; Kimstach, Tetiana V.; Solonenko, Lyudmila I.; Usenko, Ruslan V.
ENG: Slag bowls were chosen as the object of research, as important components of blast furnace, steelmaking, and ferroalloy shops of metallurgical enterprises. The main problem of operation of any slag trucks is their limited durability and frequent destruction of slag bowls. The reason for these problems is changes in the shape of the bowls during operation, manifested in the formation of narrowing places in the area of the support ring – for rail-mounted bowls, destruction of supporting pins – for rail-mounted slag trucks, or cracks in the walls. Those defects appear as a result of cyclic thermal effects of liquid slag on the bowl. Based on the results of computer simulation, it was established that the main role in the destruction of the support pins of motor-driven slag bowls belongs to temperature changes. The temperature stresses arising in the bowl are localized in the area of the slag mirror (200–250 MPa for 25L steel, 280–350 MPa for 30HML steel). The results provide grounds for improving the presented slag bowl to reduce temperature stresses in its walls and structures of the supporting trunnions. The results reported here are explained by the fact that with uneven heating of elastic bodies, temperature stresses appear, which, under certain configurations of temperature loads, lead to the destruction of structures. The findings from these studies are recommended to be used at enterprises for the design and manufacture of slag bowls, as information on the localization of dangerous places of the structure. In addition, the data presented here could be useful for metallurgical enterprises for detailed technical diagnosis of bowls in their dangerous places.
Efficient Algorithms for Parallelizing Tridiagonal Systems of Equations
(НМетАУ, Дніпро, 2021) Shvachych, Gennady Grygorovych; Vozna, Nataliіa; Ivashchenko, Olena V.; Bilyi, Oleksandr P.; Moroz, Dmytro
ENG: The article is devoted to the development of the maximal parallel forms of mathematical models with a tridiagonal structure. The example of solving the Dirichlet and Neumann problems by the method of straight lines and the sweep method for the heat equation illustrates the direct fundamental features of constructing parallel algorithms. It is noted that the study of the heat and mass transfer processes is run through their numerical modeling based on modern computer technology. It is shown that with the multiprocessor computing systems’ development, there disappear the problems of increasing their peak performance. On the other hand, building such systems, as a rule, requires standard network technologies, mass-produced processors, and free software. The noted circumstances aim at solving the so-called big problems. It should be borne in mind that the classical approach to solving the tridiagonal structure models based on multiprocessor computing systems is far more time-consuming compared to single-processor computing facilities. That is explained by the recurrence relations that make the basis of classical methods. Therefore, the proposed studies are relevant and aim at the distributed algorithms development for solving applied problems. The proposed research aims to construct the maximal parallel forms of mathematical models with a tridiagonal structure. The paper proposes the schemes to implement parallelization algorithms for applied problems and their mapping to parallel computing systems. Parallelization of tridiagonal mathematical models by the method of straight lines and the sweeping method allows designing absolutely stable algorithms with the maximum parallel form and, therefore, the minimum possible time for their implementation on parallel computing devices. It is noteworthy that in the proposed algorithms, the computational errors of the input data are separated from the round-off errors inherent in a PC. The proposed approach can be used in various branches of metallurgical, thermal physics, economics, and ecology problems in the metallurgical industry.
Graphitizing Modification of the Axial Zone of Cast Iron Rolling Rolls in the Liquidus-Solidus Temperature Range
(Dnipro University of Technology, Dnipro, Ukraine, 2023) Khrychikov, Valerii E.; Meniailo, Helena V.; Semenov, O. D.; Aftandiliants, Y. G.; Gnyloskurenko, S. V.
ENG: Purpose. To develop a method for calculating a process of graphitizing modification of unsolidificated liquid-solid zone to reduce transcrystallinity of the macrostructure and the amount of cementite in the center of castings. Methodology. The duration of solidification of the castings was determined by the kinetic curves of liquidus, solidus and pouring boundary in coordinates of relative thickness of the solidified metal layer – the parametric criterion of Gulyaev. Findings. A methodology for the process of modification of the axial zone of rolling was developed, the mass and time of adding aluminum were determined according to the amount of liquid-solid phase that remains after the solidification of the working layer. On the example of a rolling roll weighing 1115 kg, 0.488 kg of aluminum was added into liquid-solid zone after the working layer solidified. Movement of aluminum to the front of crystallization is provided by centrifugal forces and adding of aluminum along the height of the roll. Originality. For the first time, the kinetic curves of liquidus, solidus and pouring boundary have been plotted in coordinates of the relative thickness of the solidified metal layer x/R and τ/R2 – the parametric criterion of Gulyaev for rolled cast iron alloys cooled in chill-sand molds of various sizes. A methodology was developed for calculating the process of aluminum modification of the axial zone of rolling rolls after solidification of the working layer in the barrel which was set at the pouring boundary. The amount of aluminum depends on the remains of the liquid-solid phase. Practical value. Graphitizing modification reduces transcrystallinity of the macrostructure and the amount of cementite in the axial zone of castings. A promising direction for further development is the development of new methods for manufacturing castings due to physical and mechanical effects on the two-phase zone, deoxidation and alloying of the central zones of castings.
Identification of Temperature in Cupola Furnace Based on the Construction of the "Slag Composition – Slag Viscosity" Model
(TECHNOLOGY CENTER PC, Kharkiv, 2025) Nikolaiev, Denys A.; Selivorstov, Vadim Yu.; Dotsenko, Yuriy V.; Dzevochko, Oleksandr M.; Pereverzieva, Alevtyna M.; Dzevochko, Alona I.
ENG: The object of the study in the work is the temperature regime of melting in a cupola. The existing problem is that due to the aggressive high-temperature environment, continuous measurement of the parameters of the internal environment in the working space of the cupola furnace is too difficult. Even with the implementation of such a possibility, errors of the first and second types may occur. This necessitates indirect control of the temperature regime, which could provide a solution to the identification problem – whether the control system is really operating in normal mode and meets the accuracy requirements, or whether there is a parametric failure along the corresponding control circuit. The existence of the specified problem requires solutions related to the definition of criteria for evaluating the temperature regime, by which it would be possible to verify the reliable functioning of the melting control system. A criterion for evaluating the temperature regime of melting by the viscosity of the slag as a function of its composition is proposed, which allows identifying the temperature regime of melting with an accuracy of 96 %. This result is due to the proposed two-stage procedure, in which the first stage is the construction of mathematical models that describe the influence of the slag composition on the viscosity, and the second is the construction of a criterion based on the density distribution of the discriminant function for both temperature regimes. Using the obtained criterion also makes it possible to determine the areas of chemical compositions, by which the temperature regime can also be identified. The relationships between the variables for the identification procedure are presented in the form of a structural diagram. The proposed solutions will allow determining the quality of the functioning of the temperature control loop in the melting control system based on periodic control. The presented study will be useful for machine-building enterprises that have foundries in their structure, where cast iron is smelted for the manufacture of castings.
Improving a Technique for Producing a Polycomponent Semi-Finished Product with High Degree of Readiness for 3-D Printing of Functional Food
(РС ТЕСHNOLOGY СЕNTЕR, Kharkiv, 2024) Zahorulko, Andrii; Voronenko, Iryna; Bozhydai, Iryna; Pogarskiy, Aleksey; Ibaiev, Eldar; Ponomarenko, Nataliia; Bereza, Olena; Khytko, Oleksandr Yu.
ENG: The object of this study is the process of producing polycomponent semi-finished products of a high degree of readiness using a model structure of functional equipment, in particular, based on apple, Jerusalem artichoke, table beet, and sea buckthorn. A feature of the improved technique is the implementation of preliminary heat treatment with hot steam of raw materials: apple – 1.0...2.0 min, Jerusalem artichoke – 3...6 min, and table beet – 6...12 min, respectively. Sea buckthorn was not processed, only technological rinsing was used. Grinding of raw materials was carried out on a double grinding machine (apple, Jerusalem artichoke, and table beet – 0.2...0.5 10-3 m, and sea buckthorn – 0.5...1 mm). The combined production of polycomponent semi-finished products of a high degree of readiness (pastes/fractional powder) was implemented using a model structure of functional equipment. The boiling process in a rotary-film evaporator was carried out at a temperature of 55 °C for 65 seconds to a dry matter content of 25 %. Drying of the cooked multicomponent mass was carried out in a single-drum cylindrical IR dryer at a temperature of 50 °C to a final moisture content of 3...6 % and fractional grinding (0.3...0.6 mm). The rheological properties of the paste-like multicomponent semi-finished product were determined by the change in dynamic viscosity for composition 2, which is 485 Pa∙s, and in the control sample of applesauce, this indicator is 50 Pa∙s. When boiling in a rotary-film evaporator at a temperature of 55 °C to a content of 30 % of dry substances, there is an increase in the strength of dynamic viscosity by 3.2 times (600 Pa∙s), and in the control (apple paste) this indicator is 178 Pa∙s with a dry matter content of 25 %.
Influence of Ice Structure on Vitability of Frozen Sand-Water and Sand-Clay Mixtures
(Dnipro University of Technology, Dnipro, Ukraine, 2024) Solonenko, L. I.; Uzlov, Kostiantyn I.; Kimstach, Tetiana V.; Mianovska, Ya. V.; Yakymenko, D. Yu.
ENG: Purpose. To establish influence regularity of sand, water and clay preparation conditions on vitability of frozen mixtures made from combinations of these components and to increase the castings quality in foundries, as well as to improve technologies for artificial freezing of soils for underground constructions. Methodology. In this research, sand, clay, and water are used. Ice quality is estimated visually after water freezing at -15 °C in glass tubes. Frozen mixtures’ vitability at -15 °C is studied on beam-type samples. As indicators of survivability, the time to 1 mm bending of samples on supports and the time to their destruction are accepted. The time is recorded with a stopwatch, the temperature with an alcohol thermometer, the mass with electronic scales and the deflection arrow with a clock-type indicator. Findings. The presence and amount of water-soluble impurities in rare water significantly influence the nature, size and distribution of gas bubbles in ice, as well as frozen sand-water mixtures vitability. Frozen mixtures’ survivability increases with water content in them increasing, and, for sand  water mixtures, survivability is maximum if ice has a homogeneous structure. Among mixtures with clays, the mixture with non-swollen kaolin clay has the greatest vitability. Regarding survivability, recommendations for manufacturing products from frozen foundry mixtures have been developed. Originality. For the first time, deformation change kinetics (bending arrows) under the influence of beam-type samples’ self-mass from mixtures of quartz sand and water and quartz sand, clay and water frozen at -15 °C, which have been previously prepared in different ways, have been investigated. Insights into the influence of various factors and ice quality on the vitability of frozen mixtures have been further developed. Practical value. The obtained results can be useful for expanding ideas about natural frozen soils’ behavior during their cyclic temperature changes, soils artificially frozen during mine shafts elaboration, escalators’ and junctions’ tunnels, etc. when constructing subways. In foundries, the developed recommendations will reduce technological losses and will improve casting quality made using frozen casting molds and cores from sand-water or sand-clay-water mixtures, castings’ patterns and their pouring systems from sand-water mixtures.
Influence of K2ZrF6 and SiO2 on Refining Ability of Flux for Manufacturing Bimetallic Castings
(Latvia University of Life Sciences and Technologies, Jelgava, 2024) Aftandiliants, Yevhenii; Gnyloskurenko, Svyatoslav; Meniailo, Helena V.; Khrychikov, Valerii Ye.; Lomakin, Viktor
ENG: Bimetallic material is considered as an advanced functional material due to the unique physical and mechanical properties varied over the layers. Formation of bimetallic castings with steel base greatly depends on diffusion coupling with the second material working layer at elevated temperatures. The common technological problem is to remove the oxide films from the solid steel surface while its heating prior pouring melt of the working layer. This work studies the protective refining fluxes matching the selected requirements of good wetting the surfaces of solidified metal, effective protection against oxidation in the working temperature range, easy separation after pouring liquid metal and high refining capacity for oxides. The most effective fluxes based on Na2B4O7 and B2O3 compounds were used. To improve their ability to enhance wetting, work of adhesion and reduce surface decarbonization addition of K2ZrF6 and SiO2 to the flux in the amount of 3-4 wt.% was proposed and investigated. It was established that such additions increased wettability up to 9 and 20%, respectively and reduced the average rate of decarburization in the temperature range from 800 to 1000 ºС on 57 and 37%. The complete reduction of iron from scale on the steel surface was observed, while in the case of Na2B4O7 – B2O3 system it achieved 30-40% only. The mechanism explaining such a result is proposed to be due to the prevailing effect of zirconium in protecting the surface of the steel base from the oxidation and decarburization. The important result of the study is the recommendation of optimal flux composition (wt.%): Na2B4O7 – from 60 to 80; B2O3 – from 10 to 30; K2ZrF6 - from 3 to 4; SiO2 from 3 to 4. Thus, such flux could improve the production of steel based bimetallic castings and increase their properties.
Influence of Melt Properties on the Dendritic Structure of Steel Castings
(The Katowice Branch of the Polish Academy of Sciences, Poland, 2024) Aftandiliants, Y.; Gnyloskurenko, S.; Meniailo, Helena V.; Khrychikov, Valerii Ye.
ENG: The paper presents the experimental results on the determination of melt parameters such as the energy of the boundary, contact angle, density and kinematic viscosity of low and medium alloy steels at different temperatures, as well as the dispersion of their dendritic structure in solidified castings. The analysis of the data obtained allowed revealing using mathematical models the influence of the chemical composition and temperature of melts on their properties and the dendritic structure of castings. It was established the variation of the melt parameters depending on the particular chemical elements of steels as C, Si, Mn, O, P, V, Cr. The established analytical dependences shown that increasing density and viscosity contributes to the dispersion of the dendritic structure and viscosity is of the major effect. The derived quantitative patterns allows to evaluate structure formation of cast structural low and medium alloy steels.
Influence of Technological Factors on Formation Process of Bimetallic Castings
(Latvia University of Life Sciences and Technologies, Jelgava, 2023) Aftandiliants, Yevhenii; Gnyloskurenko, Svyatoslav; Meniailo, Helena V.; Khrychikov, Valerii Ye.
ENG: The analysis of the modern state of wear-resistant metallic material production showed that one of the promising directions for improving their quality is the use of bimetallic steel-cast iron castings, which have a complex of properties differentiated over the volume and surface of the products. However, the problem of obtaining a high-quality joint of the steel base and the working cast iron layers is not completely solved at present. So, the research aims to determine the quality criterion of a good diffusion joint and to study the selected technological factor influence on the formation process of bimetallic castings using the developed mathematical model. The paper examines the effect of the steel base temperature at liquid cast iron pouring over it, the temperature of pouring cast iron, as well as the ratio of liquid cast iron mass to the unit surface of the steel base on the contact surface temperature as selected quality criteria, and the structure of the transition diffusion layer of bimetallic castings. It was determined that a high-quality joint is realized when this temperature is larger than the solidus temperature of the cast iron. Moreover, the results of the mathematical model application showed maximum contribution of the liquid cast iron mass/steel unit surface ratio, less effect of the pouring iron temperature and minimum influence of the solidified steel base temperature onto the quality criteria. The metallographic analysis established the diffusion joint formation in the transition steel-cast iron layer consisting of pearlite on the side of the steel base and without the carbide matrix area on the side of the working iron layer. The results obtained are of great importance for the designing bimetallic machine parts worked under intensive wear conditions.
Intelligent Decision Support System
(RS Global Sp. z O.O., Poland, 2021) Shvachych, Gennady; Pobochij, Ivan; Sazonova, Maryna; Bilyi, Oleksandr P.; Moroz, Dmytro
ENG: Here one of the new efficient approaches to solving problems of intelligent support of making decisions of a cooperate enterprise scale is analyzed, bearing in mind that the enterprise is oriented towards integration of two interconnected information technologies: a technology of constructing information storages and a technology of intelligent data analysis. A new conception of the role of informating-controlling systems in controlling and operating pipe manufacturing process is suggested. It broadens a traditional view over information systems just as if it were only an instrument of a computer data analysis. The role of the modern information systems in the manufacturing as an independent scientific and applied direction serving as a connecting link in the triad “raw product – ngineering process – end product” is substantiated. Some problems connected with plantation of the informating-controlling systems in the pipe manufacturing is formulated. It broadens a traditional view over information systems just as if it were only an instrument of a computer data analysis. The practical application of this product permits the operating personnel of the enterprise to control the engineering process, analyze the processes passing in each mill, adjust the PRP mills’ engineering characteristics in the pipe-manufacturing process. The suggested approach influences quite strongly the production’s quality improving and enables to work stably in the thin-walled pipe grades sphere.
Kinetics of Quartz Sand and Its Mixtures Drying by Microwave Radiation
(Dnipro University of Technology, 2021) Solonenko, Lyudmila I.; Repiakh, Serhii I.; Uzlov, Kostiantyn I.; Mamuzich, I.; Kimstach, Tetiana V.; Bilyi, Oleksandr P.
ENG: Purpose. Kinetics research and description of drying by microwave radiation mechanism development of quartz sand and its mixes with sodium silicate in limited quantity of water steam medium. Methodology. Distilled water, sodium silicate solute and quartz sand have been used in this research. Study has been performed on sand samples weighing 200 g. Mixtures drying and structuring have been performed by microwave radiation with power of 700W with frequency of 2.45 GHz in air and in saturated water weighing 1 g steam medium. Accuracy of temperature measurement is 1, mass is 0.02 g. Realized in this investigation drying kinetics has been specified as specimen weight change dependence and moisture evaporation from this mixture rate vs. drying duration. Dependencies have been built on the results of video recording and corresponding chrono-gravimetric measurements data digitalization. Mixtures during heating by microwave radiation temperature changes registration has been performed with an interval of 1560 s. Samples average heating rate has been estimated by calculation based on results in their temperature change determination during first 2 minutes of heating with microwave radiation. Findings. For the first time, microwave drying kinetics of quartz sand and its mixtures with sodium silicate in limited water medium (structured by SMS-process) has been studied. For the first time, based on SMS-process material balance, analytical dependence has been developed. This dependence application allows sand-sodium-silicate mixture structured by SMS-process maximum mass to calculate when using sodium silicate solute (silicate module 2.83.0) for quartz sand cladding and 1 g of saturated water steam for mixture structuring. It has been established that when mixtures structuring according to SMS-process water extraction from them takes place in three stages at ~100, 100108 and at 125138. Maximum appropriate heating temperature of sand-sodium-silicate mixture during structuring by SMS-process has been recommended as ~125. Exceeding of specified temperature leads to hydrated water from mixture releasing in steam form and its condensation on colder working surface of model-rod rigging. Resulting condensate leads to mixture restructuring in contact with equipment places and, accordingly, sharp quality deterioration in prepared molds and rods. For manufactured molds and rods quality stabilization, it has been recommended to pre-dry the quartz sand cladded with sodium silicate solute in microwave field for at least 3 minutes before structuring according to SMS-process. Originality. For the first time, data on drying kinetics has been obtained and quartz sand and its mixtures with sodium silicate in limited water steam medium microwave drying mechanism description has been developed. Influence of number of SMS-process basic parameters on structured quartz sand weight regularities has been established. Practical value. Research results will be useful in terms of ideas expanding about the processes that accompany granular materials drying, as well as in technologies and equipment for drying and structuring fine-grained dielectric materials and their mixtures development, creating new capillary-porous media, etc. under microwave radiation influence.
Kinetics of Solidification and Crystallization of Liquid Axial Zone of Fe-C Alloys in Cylindrical Molds
(The Katowice Branch of the Polish Academy of Sciences, Poland, 2024) Khrychikov, Valerii Ye.; Semenov, Oleksandr D.; Aftandiliants, Y.; Gnyloskurenko, S.; Semenova, Tetіana V.; Meniailo, Helena V.
ENG: According to the results of digitization of the experimental studies carried out in the past concerning Fe-C alloys solidification in cylindrical molds of castings with a carbon content of 0.04%, 0.1%, 0.4%, 0.93%, 1.42%; 2.44%, 3.28%, 4.45%, 4.83% and their subsequent interpolation in the range of 0.04 ÷4.83%С there were obtained the curves of the advancement of the pour point, liquidus and solidus in the coordinates of the relative thickness of the solidified metal layer x/R and the parametric criterion τ/R2. Their usage is proposed for the development of modes of physical and chemical influence on the liquid metal in the axial zone of the casting after solidification of its calculated layer. Calculation of the mass of modifiers or deoxidizers for introduction into the axial zone was performed in relation to the total mass of metal in the liquid and liquid-solid zones of the casting. The technique for calculating the mass and time of introduction a graphitizing modifier into the axial zone of rolling rolls made of hypereutectoid steel with 1.7%C is proposed to reduce the negative impact of cementite, chromium and molybdenum carbides on the structure of the axial zone of the rolls. The obtained curves can also be used to assess the accuracy of computer modeling of the processes of Fe-C alloys solidification and further adaptation of mathematical models by the correction of thermophysical coefficients, the values of which are not always known in the liquidus-solidus temperature range.
Method of Lines in Distributed Problems of Experimental Data Processing
(RS Global Sp. z O.O., Poland, 2021) Shvachych, Gennady Grygorovych; Vozna, Nataliіa; Ivashchenko, Olena V.; Bilyi, Oleksandr P.; Moroz, Dmytro
ENG: In many cases, the mathematical support of non-stationary thermal experiments is based on methods for solving the inverse heat conduction problem (IHCP), which include boundary thermal conditions determination, identification of heat and mass transfer processes, restoration of external and internal temperature fields, etc. However, at present, the main field of the IHCP application remains the processing and interpretation of the results of the thermal experiments. It was here where the most considerable theoretical and applied successes were achieved in methods' effectiveness and the breadth of their practical use. This paper highlights the issues of mathematical modeling of multidimensional non-stationary problems of metallurgical thermophysics. The primary research purpose aims at solving problems associated with identifying parallel structures of algorithms and programs and their reflection in the computers’ architecture in solving a wide range of applied problems. Supercomputers are currently inaccessible due to the enormous cost and service price. In this regard, a real alternative is cluster-type computing systems by which the simulation results are covered in this paper. Being a relatively new technology, cluster-type parallel computing systems are useful in solving a large class of non-stationary multidimensional problems, while allowing to increase the productivity and quality of computations. The software developed in this paper can be used to plan and process the results of a thermophysical experiment. The algorithms developed in the application program package are simply reconstructed to solve other coefficient and boundary problems of thermal conductivity. The developed algorithms for solving thermophysical problems are highly accurate and efficient: the test solution for IHCP with accurate input data coincides with the thermophysical features of the sample material. The developed software for processing the results of a thermophysical experiment is self-regulating. Moreover, it is quite merely tuned to the solution of others and, in particular, of boundary IHCP.
Optimization of Production Process of Structural Steel Modified with Nitrogen and Vanadium
(Latvia University of Life Sciences and Technologies, Jelgava, 2022) Aftandiliants, Yevhenii; Gnyloskurenko, Svyatoslav; Meniailo, Helena V.; Khrychikov, Valerii Ye.
ENG: Structural steels are the most promising material, particularly in machine design. An important issue is to match their properties with the exploitation demands. It can be achieved by the optimization of the steel production process, i.e. formation of the primary and secondary structure under modification with nitrogen and vanadium, proposed in this research. At the experiments the structural steels were melted, modified with nitrogen and vanadium, subsequently deoxidized with aluminium, cerium and lanthanum. The steel samples were tested to reveal the mechanical properties and study the effect of modifying processing. The results have shown that some decrease in plastic properties, the impact strength and an increase in the critical temperature of brittleness is not due to vanadium nitride hardening of steel, but could be associated with imperfect technology. The final deoxidation of steel is often performed with aluminum of at least 0.05% in order to stabilize the grain of the structure during austenitizing heating. It was established that the necessary condition for the effective influence of nitrogen and vanadium should be a higher formation temperature of vanadium nitrides than aluminum nitrides in steels. Calculations showed that this condition is realized when the content of aluminum in steel is less than 0.03% and vanadium - 0.10%. The results of the performed experiments have shown that in this case there is a simultaneous increase in the strength properties and impact toughness of steel. Based on the obtained results the recommendations for the industrial process of steel making was formulated as below. In foundry shops with inductional melting furnaces it is necessary to additionally deoxidize steel with cerium and lanthanum. So, comprehensive optimization of the content of nitrogen, vanadium and deoxidizers in steel, as well as the temperature of austenitizing heating ensure increase in mechanical properties without reduction in plasticity and toughness.
Physicochemical Structure Features of Refractory Compositions with Inorganic Binders
(Vasyl Stefanyk Precarpathian National University, Ivano-Frankivsk, Ukraine, 2022) Liutyi, R. V.; Solonenko, L. I.; Osipenko, I. O.; Fedorov, M. M.; Moroz, B. I.
ENG: The article presents the study results of new inorganic binders and the physicochemical processes of their formation. The main purpose of the created materials is to make molds and cores for foundry production. Creating environmentally-friendly binders with a set of functional properties for foundry production is relevant worldwide. Therefore, scientists from different countries are paying special attention to the study of silicate and phosphate binders. The study analyzes the kinetics of the orthophosphoric acid interaction with several inorganic materials – pulverent pyrophyllite, disthene-sillimanite, a by-product of electrocorundum production, and sodium chloride. The phase and chemical composition of all formed binders have been established. In aluminum-containing compositions, those are represented by aluminum orthophosphates in crystalline and amorphous forms. Sodium metaphosphate is formed in the composition with sodium chloride. Peculiarities of the structuring compositions physical process with liquid glass and granular quartz filler due to steam-microwave treatment are determined. It is shown that structuring occurs due to dehydration, which is completed within 4…12 min, which allows reducing the liquid glass content in the composition to 1.5% while ensuring a high level of strength. The properties of structured compositions with the developed binding components are researched, and it is shown that all of them are competitive. Recommendations for their possible application were created.
The Process of Vacuum Formation in the Shrinkage Cavity at Castings Crystallization
(The Katowice Branch of the Polish Academy of Sciences, Poland, 2022) Khrychikov, Valerii Ye.; Semenov, Oleksandr D.; Meniailo, Helena V.; Aftandiliants, Y.; Gnyloskurenko, S.
ENG: The formation process of one of the most common casting defects, a shrinkage depression concerned to shrinkage cavity, was studied. The methodology, device and the experimental set up were developed to study the shrinkage cavity growth. The kinetics of vacuum formation in the cavity of the spherical casting of Al-Si-Mg alloy at its solidification in the sand-and-clay form was investigated. The data were analysed taking in mind the temperature variation in the centre of crystallizing casting. The causes of the shrinkage depression in castings were clarified. It was determined that atmospheric pressure leads to the retraction and curvature of metal layer on the surface of the casting with lower strength below which the shrinkage cavity is formed. To avoid such defects it was recommended to use the external or internal chills, feeders and other known technological methods. Deep shrinkage cavities inside the castings could be removed with an air flow through a thin tubular needle of austenitic steels for medical injections.

Browse

Browsing Кафедра ливарного виробництва (ДМетІ) by Title

Results Per Page

Sort Options